Tie-down Vector Dynamics Foundation System for Wind Zones l Manual do Utilizador

TIE DOWN ENGINEERING • 255 Villanova Drive SW • Atlanta, GA 30336www.tiedown.com (404) 344-0000 Fax (404) 349-0401 Vector DynamicsFoundation Systems

Vector Dynamics Systemfor Concrete ApplicationsInstructions (1 of 3)The Vector system for concrete pads applies to concrete footers, runners and slabs

9. Putawasherandnutononeofthe3/8”x3-3/4”wedgeanchors.Thenutshouldbescrewedon enough to have 1 or 2 threads showing on the top

Vector Dynamics Systemfor Concrete ApplicationsInstructions (3 of 3)Single Longitudinal System#59036Double Longitudinal System#5904618. Installlongi

13 Revised: 8/19/08Asphalt InstallationsThese instructions are for portable classrooms, offices or other structures using I-beam frames. Read and fo

Example of a Single Section 14' x 72' HomeWIND ZONE I for Single Section HomesUsing Vector Dynamics Foundation SystemsSoil Classifications:

D1030 Tie Down Engineering 255 Villanova Drive SW Atlanta, Georgia 30336 (404) 344-0000 • Fax (404) 349-0401www.tiedown.comExample of a Double S

D1030 Tie Down Engineering 255 Villanova Drive SW Atlanta, Georgia 30336 (404) 344-0000 • Fax (404) 349-0401www.tiedown.comExample of a Triple S

D1030 Tie Down Engineering 255 Villanova Drive SW Atlanta, Georgia 30336 (404) 344-0000 • Fax (404) 349-0401www.tiedown.comExample of a Double S

D1030 Tie Down Engineering 255 Villanova Drive SW Atlanta, Georgia 30336 (404) 344-0000 • Fax (404) 349-0401www.tiedown.comExample of a Single S

D1030 Tie Down Engineering 255 Villanova Drive SW Atlanta, Georgia 30336 (404) 344-0000 • Fax (404) 349-0401www.tiedown.comExample of a Double S

IntroductionThese instructions describe the proper use of the lateral and longitudinal foundation system. You may also refer to the home manufacturer’

D1030 Tie Down Engineering 255 Villanova Drive SW Atlanta, Georgia 30336 (404) 344-0000 • Fax (404) 349-0401www.tiedown.comExample of a Triple S

D1030 Tie Down Engineering 255 Villanova Drive SW Atlanta, Georgia 30336 (404) 344-0000 • Fax (404) 349-0401www.tiedown.comExample of a Single S

D1030 Tie Down Engineering 255 Villanova Drive SW Atlanta, Georgia 30336 (404) 344-0000 • Fax (404) 349-0401www.tiedown.comExample of a Double S

D1030 Tie Down Engineering 255 Villanova Drive SW Atlanta, Georgia 30336 (404) 344-0000 • Fax (404) 349-0401www.tiedown.comExample of a Triple S

Vector DynamicsFoundation Systemsby TIE DOWN ENGINEERINGInstallation Notes

50 in. max.Figure 150 in. max.24”26” MaximumUnequal Pier HeightsHomeswithunequalpierheightsarelimitedto50”maximumpierheight.Thedifference

081308,D973Unit Width Max. Pier Height Max. Sidewall Height Max. Unit Length for Number of Vector Systems 2 3 4 5 6 136 32" 96"

Vector DynamicsFoundation SystemsComponent Parts ListVector System 2000Part # 59018Single piece pads with strapsand slotted boltsConcrete Vector Syste

Longitudinal Hardware KitPart#59026(forusewith59271)Vector Lateral Hardware KitPart # 59024(forusewith59271)Struts for Longitudinal SystemsP

A C B Long U-Bolts#59018System#10733 HardwareTie Bracket Beam Clamp Longitudinal Strut Longitudinal Bracket Vector 2 sq. ft.Pad for singlelongitudinal

I-BeamBeam ClapStrut3 Sq. Ft Vector Pa dfor Double Block SetLongitudinal BracketABDCOutside TensionBracket:Set-Up Instructions forDouble Stack Vector

For metal piers, place the piers in the center of the Vector pads. Setthesingle4x4ortwo2x4’sthroughthepiers,centeredintheU-bolts,sotha